A Disposable Brush And A Few Rags Build An Awesome Finish. Finishing is a challenging aspect of woodworking. There are many finishing materials and methods of application; within a single piece there may be several conditions requiring different approaches. It is one thing to get a nice finish on a small flat sample board but…

We all have to begin somewhere, and this is actually the most difficult time. Years ago I remember teaching a class about finishing that included one student who said he had never used a stain or finish, and to make matters worse, he had never even painted anything. This was a two-day class in which…

A simple approach to this classic finishing technique. Finishing options abound in the woodworking world, however with Arts & Crafts style pieces, you need to get the finish right to complete the feel of the piece. This isn’t a project made from birch plywood, where an opaque finish might suffice. There are several finishing schedules I’m…

Learn to set up and wield one of the most useful (and inexpensive) handplanes. Also check out: A primer on adjusting wooden planes. Kevin Drake, a furniture maker who trained under James Krenov, stood before his wonky-topped workbench one day many years ago and hesitated. His urge was to start flattening the benchtop by planing across…

Basic steps for beautiful joints. Dovetails. They get put on a pedestal as a sign of quality. And while not every project or furniture style warrants them, I enjoy sitting down, listening to an audiobook, and cutting them by hand. Once you break down dovetails into a series of basic steps, I think you’ll find…

The difference is more than just pushing or pulling. It’s been over 20 years since the Western handsaw, a tool that cuts on the push stroke and was the pride of the English-speaking world, was surpassed as the tool most woodworkers reached for when they need a handsaw. It has been replaced by the Japanese…

This traditional joint ensures the only cup on your tabletop will have coffee in it. The breadboard end is a traditional device for preventing a broad panel such as a tabletop from cupping. It is a narrow strip of wood that runs across the end of the main panel. Obviously, it must be attached in…

A system as elegant as the joint itself. Compound-angle dovetails are some of the most beguiling joints in all woodworking. But, as John Lennon once suggested, they can be as difficult to make as “fixing a hole in the ocean.” Well, maybe not that hard—but it all begins with figuring out  those odd angles. I’ve…

Fine furniture calls for an elegant drawer. A master cabinetmaker shares his approach to design and fitting. There are just a few things my partner at Philadelphia Furniture Workshops, Alan Turner, and I don’t see eye-to-eye on. But how to make a good drawer isn’t one of them. When building furniture, we probably spend as…

When using my miter saw, I’ve found that the easiest way to sneak up on a line is to use a stack of sticky notes. First, set a stop block to cut your part slightly oversize (1/16″ is plenty). Attach a thin pile of sticky notes to the stop block, make a cut, and then…

I use a portable circular saw to break down plywood and other sheet goods into manageable pieces before bringing them to the table saw for final sizing. I prefer to do the job on sawhorses rather than crouching on the floor. Unfortunately, you normally need three or four horses to provide enough support to prevent…

The next time you use your jigsaw, forget about hauling out the sawhorses or cantilevering a hard-to-hold workpiece off your bench. Extruded polystyrene insulation board, the rigid pink sheets used in housing construction, makes sawing easy, whether you’re cutting a small piece of hardwood or a full sheet of plywood. During the cut, the workpiece…

When gluing plastic laminate to a substrate, lots of folks use sticks or dowels to support the laminate. Supports allow you to perfectly position the laminate, since it can’t be shifted once it contacts the glue. I use old mini-blinds, curved side down. Mini-blinds are easy to pull out and easy to clean. -J.A.Wilson

When I clean my HVLP spray gun, this shop-made container captures the liquid solvent and fumes. When the gun is clean, I simply pour the waste into a storage container for disposal. Drill a 3-in. hole in the back of a paint thinner jug. Cut a 3-in. circle from an activated carbon filter pad (available…

If you do a lot of spray painting and finishing, but don’t have room for a permanent finishing bench, give this turntable a spin. It’s surprisingly sturdy and because it rotates, you can get to all sides of your project while standing in one spot. It’s lightweight, so it can easily be taken outside. When…

Tool: Scriber Buy Now Manufacturer: Tooley Park MSRP: £28 There are often times, where there’s simply no substitute for the right tool. A good scriber is one of those tools. Whether its leveling chair legs, scribing a cabinet, or any number of tasks, a quality scribe earns its keep here. Some of the best scribes I’ve…

Tool: Stainless Steel Precision Rulers Shop Now  Manufacturer: JessEm MSRP: $24.99+ The Canadian company JessEm, known for their high-quality router lifts, recently released a new line of precision steel rules. As you can see in the photo above, what makes these rules different than others is the laser-cut shapes in the center. These shapes are…

Tool: Magnetic Straightedge Shop Now  Manufacturer: Lee Valley MSRP: $7.50 Don’t have a drafting table? Can’t draw freehand to save your life? Here’s a tool from Lee Valley that lets you easily make isometric shop sketches. The tool has two parts: a standard 12″ ruler with a matte finish and an innovative black straightedge. Seven…